.png)
Français (Canada)
CAD-CUT® P.S. GLITTER ADHESIVE VINYL
Material Overview
Use your vinyl cutter to create sparkling decals with P.S. Glitter. This easy-to-use, calendared pressure-sensitive vinyl features a smooth glitter finish and brilliant shine. Available in 17 vibrant colours, this material is soft, pliable, and safe for indoor or outdoor use. Apply to almost any hard surface, including tumblers, mugs, signs, and more.
Note: This media is not for digital printing.
- For indoor/outdoor application
- Recommended for general purpose permanent application: signs, banners, window graphics, tumblers, and most hard goods
- Not recommended for use with microwave or dishwasher or near heat/flame source
- 76.2 micron thickness
- Not laser cutter compatible
- Squeegee and ORATAPE Patterns mask recommended for application
Note: This media is not for digital printing.
Image slider
Benefits at a Glance
User Guide
Application Instructions- Place vinyl with the liner side down into cutter and cut your design. (DO NOT reverse/mirror your design.) Weed away excess vinyl.
- Mask your design using ORATAPE mask, making sure to smooth out any bubbles with a plastic squeegee.
- Remove masked graphic from liner and stick to center of application surface. Using firm and even pressure, squeegee the graphic from the center outward, past the edges of the design.
- Starting in a corner, peel back the ORATAPE at a 180° angle while pressing the tape against the graphic with your hand.
- Feel for any edges, bubbles, creases, or parts of the graphic that are not flat. Press down firmly with your hand and work out the problem area until the graphic is completely smooth.
Cutter Instructions| Cutter | Blade | Force | Offset | Speed |
|---|---|---|---|---|
| Graphtec | 45° | 6-8 | 1 | 25 cm/s |
| Roland GS-24 | 45° | 90-110 | 0.250 | 30 cm/s |
| Silhouette Cameo | Autoblade | 4 | N/A | 8 |
| Cricut Maker 5 | Fine-Point | Glitter Vinyl | N/A | N/A |
Note: Cut the design in the positive (facing up). You should always test cut prior to any production run. For optimal cutting and weeding, maintain a line thickness of at least 1/8” for logos.
CAD-CUT® P.S. GLITTER ADHESIVE VINYL
Create Dazzling Hard Goods
Material Overview
Use your vinyl cutter to create sparkling decals with P.S. Glitter. This easy-to-use, calendared pressure-sensitive vinyl features a smooth glitter finish and brilliant shine. Available in 17 vibrant colours, this material is soft, pliable, and safe for indoor or outdoor use. Apply to almost any hard surface, including tumblers, mugs, signs, and more.
Note: This media is not for digital printing.
- For indoor/outdoor application
- Recommended for general purpose permanent application: signs, banners, window graphics, tumblers, and most hard goods
- Not recommended for use with microwave or dishwasher or near heat/flame source
- 76.2 micron thickness
- Not laser cutter compatible
- Squeegee and ORATAPE Patterns mask recommended for application
Note: This media is not for digital printing.
Image slider
Benefits at a Glance
Available Colours
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
Hover image
User Guide
Application Instructions- Place vinyl with the liner side down into cutter and cut your design. (DO NOT reverse/mirror your design.) Weed away excess vinyl.
- Mask your design using ORATAPE mask, making sure to smooth out any bubbles with a plastic squeegee.
- Remove masked graphic from liner and stick to center of application surface. Using firm and even pressure, squeegee the graphic from the center outward, past the edges of the design.
- Starting in a corner, peel back the ORATAPE at a 180° angle while pressing the tape against the graphic with your hand.
- Feel for any edges, bubbles, creases, or parts of the graphic that are not flat. Press down firmly with your hand and work out the problem area until the graphic is completely smooth.
Cutter Instructions| Cutter | Blade | Force | Offset | Speed |
|---|---|---|---|---|
| Graphtec | 45° | 6-8 | 1 | 25 cm/s |
| Roland GS-24 | 45° | 90-110 | 0.250 | 30 cm/s |
| Silhouette Cameo | Autoblade | 4 | N/A | 8 |
| Cricut Maker 5 | Fine-Point | Glitter Vinyl | N/A | N/A |
Note: Cut the design in the positive (facing up). You should always test cut prior to any production run. For optimal cutting and weeding, maintain a line thickness of at least 1/8” for logos.